Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
We have stumbled on this article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and reckoned it made good sense to relate it with you in this article.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is conveniently available, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Make certain you have actually certified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will assist you mount a new bathtub in your shower room if you have already purchased a brand-new tub and do not need to transform the arrangement of your previous supply of water pipelines.
Your tools and also material checklist need to comprise the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the restricted access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible tap connector to the proper supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water supply and check all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the bath tub and additionally examine the overflow outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and sealing around the bathtub needs to wait until the bathtub has been used at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in location between the tap and the sink. Secure the tap in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind ought to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in difficulties with moisture and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to allow for the activity experienced when the bathtub remains in use. The sealer can split relatively early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed reading the entire entry. Please take the time to promote this post if you liked it. Bless you for your time. Please visit our blog back soon.
Course Detail
Report this page